320 RX slide wit a Romeo 1 help - Page 2 - SIG Talk
SIG Talk Gun Forum

320 RX slide wit a Romeo 1 help

This is a discussion on 320 RX slide wit a Romeo 1 help within the P250, P320, & P320 X-5 Pistols forums, part of the SIG Sauer Pistols category; I also purchased a P320 with Romeo installed. Out of case the dot was so far right I wasn't on the paper at 15 yards. ...


Go Back   SIG Talk > SIG Sauer Forum > SIG Sauer Pistols > P250, P320, & P320 X-5 Pistols

P250, P320, & P320 X-5 Pistols P250, P320, & P320 X-5 Pistols

Like Tree4Likes
Reply
 
LinkBack Thread Tools Display Modes
Old 08-01-2020, 03:55 AM   #16
Junior Member
 
GregNH's Avatar
 
Join Date: Jun 2020
Posts: 28
Likes Received 31
I also purchased a P320 with Romeo installed.
Out of case the dot was so far right I wasn't on the paper at 15 yards.
I got it sighted in , but I don't care if the the iron sights match or not.
I have issues while wearing contacts or glasses with iron sights so using the Romeo eliminates the need to use the iron sights if that makes sense.
With my old eyes, it's either see the sights and blurred target or see the target and blurred sights.
The Romeo is a game changer for me
It's tough getting old.

Good luck
Lab4Us likes this.
GregNH is offline  
Register

Welcome to the SIG Talk Forum dedicated to SIG Sauer Pistols and SIG Sauer Rifles.

We welcome everyone and the community is free to join so register today and become part of the SIG Talk Forum!

Old 08-01-2020, 04:49 AM   #17
Supporting Member
Supporting Member
 
DIRTBOY's Avatar
 
Join Date: Apr 2020
Location: SFLA
Posts: 201
Likes Received 78
Quote:
Originally Posted by GregNH View Post
From another post on here "Zeroing my Romeo 1 on X carry"
rcbrough quoted:

It is not normal. I have had to send back two Romeo1s to the mother ship. With mine both would not adjust the windage far enough to the left to cowitness the irons. One brand new straight out of the box. The other after about 600 rounds. Call CS and they will walk you through the steps to send it back in for inspection and repair.

Hope this helps
Thanks! Thats my issue.
DIRTBOY is offline  
Old 08-01-2020, 06:47 AM   #18
Supporting Member
Supporting Member
 
saudadeii's Avatar
 
Join Date: Dec 2012
Location: SoCal, CA
Posts: 1,802
Likes Received 717
So my RX slide came sighted in slightly high and to the right.

I put a target up on my wall approx 20 feet away and aimed using the iron sights until I had a decent sight pic (gun was held in a vise) Turned on the Romeo, found the dot, dot was high and right. Had to turn elevation and windage a full turn to get the dot on the center of the target. Moved my head around while still seeing the dot to check for parallax (not too bad). Will fine turn when I get to the range.

I basically did the same with my M&P and RMR. The RMR only needed a couple more clicks to get it where I wanted it once at the range.
saudadeii is offline  
 
Old 08-01-2020, 10:05 AM   #19
Senior Member
 
Join Date: Feb 2013
Location: Tx
Posts: 135
Likes Received 37
DB - maybe, adjust the dot to the other side of the window. Then bring it to the middle, not worried about elevation yet. Go to your range and set up at 10 yards. Draw a 4" circle on the paper. Put the dot in the center of the circle and shoot. Move the dot until your rounds are in the circle. May or may not work. If not then I would contact Sig. Good luck.
drnls is offline  
Old 08-02-2020, 03:13 AM   #20
Senior Member
 
Join Date: Nov 2017
Location: NW Arkansas
Posts: 1,177
Likes Received 569
Sounds like another in the long line of defective R1's. I get Sig is just waiting for the day when all the R1's will be 5 years old and they don't have to honor the warranty anymore.
jejb is offline  
Old 08-02-2020, 04:39 AM   #21
Senior Member
 
Lab4Us's Avatar
 
Join Date: Jul 2018
Location: West Texas
Posts: 1,607
Likes Received 1776
Quote:
Originally Posted by jejb View Post
Sounds like another in the long line of defective R1's. I get Sig is just waiting for the day when all the R1's will be 5 years old and they don't have to honor the warranty anymore.
Guess its at least another 5 years since I just bought a new one last month! Mine both work great and were easy to zero in at the range. The 3 year old one on my P229 is still holding dead center zero.
Lab4Us is offline  
Reply

  SIG Talk > SIG Sauer Forum > SIG Sauer Pistols > P250, P320, & P320 X-5 Pistols

Thread Tools
Display Modes



Top Gun Sites Top Sites List

Powered by vBulletin 3.8.8
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.6.1
Copyright © 2010 - 2020 SIG Talk. All rights reserved.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.SIG Talk is a SIG Sauer Firearms enthusiast's forum, but it is in no way affiliated with, nor does it represent SIG Sauer, Inc. of Exeter, NH.