This is a discussion on is this normal? within the SIG Sauer Pistols forums, part of the SIG Sauer Forum category; New German Sig p226 I put around 150 rounds through it and the bottom of the barrel feed ramp is 2 little grooves where the ...
|SIG Sauer Pistols SIG Sauer Pistol Forum: SIG Sauer Pistols - P210, P220, P224, P225, P226, P227, P228, P229, P232, P238, P239, P245, P250, P290, P320, P365, P522, P556, PM400, SP2022, Mosquito,|
| ||LinkBack||Thread Tools||Display Modes|
|12-23-2011, 05:07 PM||#1|
is this normal?
New German Sig p226 I put around 150 rounds through it and the bottom of the barrel feed ramp is 2 little grooves where the metal looks like its hitting something, they are really tiny grooves now. I haven't had any problems yet not one failure. I'm just wondering if its normal for this to happen?
Last edited by surtac100; 12-23-2011 at 05:16 PM.
|12-23-2011, 05:25 PM||#3|
Can you post a picture of the locking block as well?
Looking at a zoomed photo, I am having some difficulty seeing it clearly enough to determine what may be there with confidence. Can you get more light on the subjet and get some different angles?
Last edited by Reliable; 12-23-2011 at 05:36 PM.
| || |
|12-24-2011, 03:09 AM||#5|
The bottom of the feed ramp looks like its hitting on the edge of the piece under it, I didn't think the barrel moved that far up to even hit that edge.
Could it have been from using cheap ammo?
Last edited by surtac100; 12-24-2011 at 03:19 AM.
|12-24-2011, 04:12 AM||#6|
I thought that is what you were refering to in the original picture, just wanted to be sure.
That is a condition that I have not seen. I too thought that the forward travel would not have gone to the front edge of the locking block. It almost looks like some where along the way it was mis-assembled and bound up. Can't figure out how because I tried to get that amount of travel out of both of my 226's and came no where close. I do want to add, though, that the wear marks on my locking blocks go all the way to the front edge.
It does not look like it would have any effect on feeding, but it does look like it "could" catch on the locking block.
My suggestion would be to send the pictures and a description to Sig customer service and see what they have to say.
Last edited by Reliable; 12-24-2011 at 04:46 AM.
|04-27-2012, 06:42 AM||#9|
Join Date: Apr 2012
Just bought a P229 Enhanced Elite 9mm, I think I am having somewhat of the same issue....How did this end for you, did you contact Sig and if so what did they suggest or do for you. I noticed it just putting my slide back on after cleaning.
|Search tags for this page|
barrel ramp stuck in locking block,
chip bottom of slide sig p229,
glock 42 barrel ramp stuck under locking block,
p226 bottom view,
sig p226 barrel overhanging locking block,
sig p226 feed ramp close up,
sig p229 feed ramp,
sig p229 feed ramp burs,
sig p229 feed ramp wear,
sig underside rail wear,
sig wear on underside of barrel,
sp2022 not feeding
Click on a term to search for related topics.
|Similar SIG Talk Discussions|
|Thread||Thread Starter||Forum||Replies||Last Post|
|Normal Wear P226 Legion Slide Rails?||JZ2123||Legion Series||19||07-01-2018 05:19 PM|
|Is this normal wear?||Bourget117||SIG Sauer Pistols||8||12-19-2017 10:45 AM|
|Is this normal? (scratching on right side of slide's chamber area)||Roo||SIG Sauer Pistols||39||11-15-2017 04:02 PM|
|Normal wear on CPO ?||Jefe||SIG Sauer Pistols||7||08-12-2017 07:04 AM|
|Is this normal wear on brass being ejected?||Jwcash||SIG Sauer Pistols||7||02-12-2017 07:15 PM|